Skip to content

Plain-language guides to ATV and quad ownership and riding

Friday, November 20, 2026

Search

ATV Chain and Drive: Inspection, Tension and Lubrication

how to adjust atv chain

Not sure how to adjust ATV chain slack without guessing? Lift the rear wheels, loosen the axle housing, turn the jam nuts evenly, set the deflection your manual gives, then torque everything back.

This page is one part of our wider guide to atv maintenance, which covers the checks around the drivetrain.

Item Value
Manual used as the example 2022 Outlaw 70 Owner’s Manual
Drive chain tension 1/4″-1/2″ (6-12 mm) deflection
Eyelet screw jam nut torque 20 ft-lbs (27 N·m)
Axle bearing housing fastener torque 37 ft-lbs (50 N·m)
Wheel lug nut torque 30 ft-lbs (40 N·m)

These figures come from the Polaris owner’s manual page on drive chain slack adjustment. They apply to that one model and can change, so check the source and your own manual before you rely on them.

What does a chain-drive ATV need from you?

Some ATVs, particularly small youth models, send power to the rear axle through a drive chain. Unlike a shaft drive, a chain needs regular attention from the owner: it has to be kept lubricated, checked for slack and adjusted when it drifts out of range.

The Polaris manual treats this as three separate jobs. It has one section on drive chain lubrication, one on slack inspection and one on slack adjustment, all under the heading “Drive Chain”, as the manual’s contents list shows.

The order matters. You inspect first, and you only adjust if the slack is outside the range your manual allows.

Safety first: read your own manual

The same manual states that it contains warnings, instructions and other information you must read and fully understand before riding or performing maintenance, according to the Polaris page. Treat that as the starting point for any chain job.

Everything below is a description of one manufacturer’s procedure for one model. Your machine may use different fasteners, a different layout or different numbers, so your own manual always wins over a general article.

Before you start, gather what the job calls for:

  • A stand or lift that holds the rear of the vehicle securely.
  • Wrenches and sockets that fit the jam nuts, axle housing fasteners and wheel nuts.
  • A torque wrench, because every fastener on this job has a specified value.
  • Your owner’s manual, open at the chain section.

The tire and battery side of a service day is covered elsewhere: see our notes on atv tire pressure and atv battery maintenance.

Lubrication and slack inspection

A chain that is dry or loose wears faster and is harder to set correctly, so lubrication and inspection belong together. Your manual names the lubricant and the interval, and neither is repeated here because the source pack for this page does not give them.

When you inspect slack, you are measuring how far the chain can be pushed or pulled from its resting position. That movement is called deflection, and it is the number your manual gives as the target.

For the Polaris model used here, the drive chain tension is 1/4″-1/2″ (6-12 mm) deflection, per the manual’s adjustment page. If your chain already sits inside your own manual’s range, leave the adjusters alone.

How to adjust ATV chain tension step by step

The steps below follow the Polaris procedure for the 2022 Outlaw 70. Work through them in order and repeat the adjustment on both sides of the vehicle.

  1. Lift the vehicle so both rear tires are off the ground.
  2. Optionally remove both rear tires to make the fasteners easier to reach.
  3. Loosen the four axle bearing housing fasteners.
  4. Loosen either the inner or the outer eyelet screw jam nuts on each side of the vehicle.
  5. Turn the outer jam nut clockwise to take up slack until the chain tension is at specification.
  6. Repeat on the other side of the vehicle.

The manual stresses one point: adjust each jam nut equally. Uneven adjustment can leave the axle out of square, so count turns on each side and compare as you go. All of these steps are listed on the Polaris procedure page.

A rider sits on an ATV silhouetted against the low sun.

Tightening everything back to specification

Setting the slack is only half the job. Once the chain tension is right, you torque each fastener you loosened, and the manual gives a value for each.

Fastener Torque
Eyelet screw jam nuts (outer) 20 ft-lbs (27 N·m)
Axle bearing housing fasteners (four) 37 ft-lbs (50 N·m)
Wheel lug nuts 30 ft-lbs (40 N·m)

The values above are taken from the same Polaris page, and they can change between model years, so check the source for your own machine.

Follow the order in the manual: jam nuts first, then the axle bearing housing fasteners, then the wheel nuts if you took the tires off. Skipping the wheel nuts is an easy mistake when you only lifted the wheels briefly.

Common mistakes to avoid

  • Adjusting one side more than the other, which the manual warns against.
  • Forgetting to loosen the axle housing fasteners before turning the jam nuts.
  • Skipping the torque wrench and tightening by feel.
  • Using numbers from a different model instead of your own manual.
  • Adjusting a chain that was already within range.

If the chain cannot be brought into range, or something looks damaged, stop and have the machine checked by a qualified technician rather than forcing the adjusters.

Frequently asked questions

Do I have to take the rear tires off?

Show answer

No. The Polaris procedure lists tire removal as optional and only suggests it for easier access. You do need both rear tires clear of the ground, as the manual describes.

Which jam nut do I turn to tighten the chain?

Show answer

On the model in the manual, you loosen the jam nuts first and then turn the outer one clockwise. Your machine may differ, so confirm the direction in your own manual.

Can I use these torque numbers on any ATV?

Show answer

No. They belong to one Polaris model and one manual edition. Look up the values for your vehicle before you reach for the torque wrench.

Where can I find the lubrication details?

Show answer

In your owner’s manual, which for the Polaris example has a dedicated drive chain lubrication section next to the inspection and adjustment sections. A dealer or qualified technician can also confirm what suits your machine.