If your ATV won’t start, you’re most likely facing a weak battery, stale fuel or a fouled spark plug. Check them in that order, because each test is quick and cheap.
This guide is one part of our wider coverage of atv maintenance, and it shows how routine care heads off most starting problems.
| Item | Value |
|---|---|
| Healthy 12-volt battery, engine off | About 12.6 volts |
| Charge the battery if it reads below | 12 volts |
| Typical spark plug gap | 0.028 to 0.035 inches |
| Wait after clearing a flooded engine | 10-15 minutes |
These figures come from a spark plug maker’s ATV no-start guide. Figures can change and vary by model, so check the source and your owner’s manual before you rely on them.
Start with the battery
A dead or weak battery is the most common culprit, according to the same guide. Even when the lights work, the battery may not have enough power to crank the engine.
Use a multimeter to read the voltage with the engine off. A healthy 12-volt battery should read around 12.6 volts, and a reading below 12 volts means an overnight charge, as the guide explains.
- Clean corrosion from the terminals with a wire brush and a baking soda solution.
- Tighten the cables, since loose connections can stop proper electrical flow.
- Charge the battery overnight and test it again.
- If charging fails, try a jump-start from another vehicle or a portable jump starter, letting the donor vehicle run for a few minutes first.
Check the fuel system
Old fuel causes trouble, especially when an ATV has sat in one place for months. Many riders simply forget to fill up after the last ride of the season.
Smell and look at what is in the tank. As the source guide puts it, if gas smells varnish-like or looks cloudy, you should drain the tank and refill it with fresh fuel.
Then look at the filter. Most ATVs have an inline fuel filter between the tank and the carburetor, and a clogged one blocks gas from reaching the engine.
- Remove the filter and hold it up to the light.
- If you can’t see through it clearly, replace it.
- Some filters sit inside the tank, which takes more work to reach.
What is the spark plug telling you?
Remove the plug with a spark plug socket and look closely at the electrode. Its condition points to the likely fault.
- Light tan or gray with no heavy carbon buildup: a healthy plug.
- Black and sooty: a rich fuel mixture or oil burning.
- White: lean running conditions or overheating.
- Wet: the fuel isn’t igniting properly.
Replace a damaged plug with the correct heat range for your model. The gap matters as well: most ATVs call for 0.028 to 0.035 inches, measured with a feeler gauge, but your owner’s manual has the exact figure, as the guide notes.

Air filter, carburetor and flooding
A dirty air filter restricts airflow to the engine. Hold it up to the light, and if light doesn’t pass through easily, clean or replace it.
The type of filter decides the fix: paper filters need replacing when dirty, while foam filters can be washed in soap and water and must dry completely before they go back in. If the filter is grimy, our guide on how to clean an atv covers wider washing habits.
The carburetor mixes fuel and air, and dirt, old fuel and moisture can clog its tiny passages. Carburetor cleaner spray helps, paying attention to the jets and passages. A thin wire can clear stubborn blockages, but avoid enlarging the holes.
A carburetor can also flood with too much fuel. Remove the spark plug and crank the engine several times to clear the excess, then wait 10-15 minutes before refitting the plug and trying again, per the guide.
Starter system, kill switch and safety switches
On electric-start models, the sound you hear is a clue. A click when you press the start button may mean a bad starter solenoid, while a grinding noise suggests worn starter gears or a weak starter motor.
The starter draws heavy current, so corroded or loose connections can stop it working. Clean them with electrical contact cleaner and tighten them securely.
Also rule out the simple things. Make sure the kill switch is in the run position and the gear selector is in park or neutral, because modern ATVs have safety switches that prevent starting under certain conditions.
Once you have found the fault, add these checks to your atv service schedule so they happen before the next ride rather than after a breakdown.
Frequently asked questions
Can I use a pull cord or kick-starter if the button does nothing?
Show answer
Many ATVs carry a backup kick-start or pull-start system. Trying it can show whether the fault lies in the starter system or in the engine itself.
Why won’t my ATV start after sitting all winter?
Show answer
Fuel that has stood for months is a frequent cause, so inspect it before anything else. A battery left idle may also have drained, which is why the voltage test is worth doing early.
How do I keep stale fuel from causing problems again?
Show answer
After refilling with fresh fuel, add a fuel stabilizer. That is the guide’s suggested way to prevent the same problem from returning.
When should I give up and call a mechanic?
Show answer
The guide says most starting problems can be solved at home with basic steps. If you have worked through the battery, fuel, plug, air, carburetor and starter checks and the engine still refuses, a qualified mechanic is the sensible next call.



