Skip to content

Plain-language guides to ATV and quad ownership and riding

Friday, November 20, 2026

Search

How to Change ATV Engine Oil Step by Step

atv oil change

Planning an atv oil change and unsure where to begin? Warm the engine for two to three minutes, drain the oil, fit a new drain-plug washer, and replace the filter with every oil change. Here is the sequence.

This guide is one part of a wider look at atv maintenance, so read it alongside the routine checks covered there.

Item Value
Engine warm-up before draining Two to three minutes, until warm
Oil filter Replace at every oil change
Time allowed without oil A few hours at most; never overnight
Drain plug washer New sealing washer on reinstall
Work surface Level ground

The figures come from the oil and filter change page of a Polaris owner’s manual, published online by the manufacturer. Manuals get revised and other models differ, so check the source before you rely on them.

What to prepare before an ATV oil change

The manual says to obtain the correct oil filter and an adequate supply of oil so the job can finish without interruption, as the Polaris owner’s manual puts it. That matters because the engine sits empty for part of the work.

Gather these before you loosen anything:

  • The correct oil filter for your model
  • Enough fresh oil to refill the engine
  • A new sealing washer for the drain plug
  • A drain pan for the crankcase
  • An oil filter wrench
  • Towels and a clean, dry cloth

Change the oil and filter at the intervals in your machine’s periodic maintenance chart, because the manual treats that chart as the schedule to follow (source). For the wider picture of recurring jobs, the atv service schedule page is the place to look.

Step-by-step: draining the engine oil

The sequence below follows the procedure in the 2022 Phoenix 200 Owner’s Manual. Other machines can differ, and that manual tells readers to understand its warnings and instructions before doing maintenance, so treat your own manual as the final word.

  1. Park the vehicle on a level surface.
  2. Clean the area around the drain plug on the bottom of the engine crankcase.
  3. Run the engine for two to three minutes until warm, then stop it.
  4. Place a drain pan beneath the crankcase and remove the drain plug.
  5. Let the oil drain completely.
  6. Check that the sealing surfaces on the plug and crankcase are clean and free of burrs, nicks or scratches.
  7. Fit a new sealing washer on the drain plug, reinstall the plug and tighten it to the specified torque.

The engine is warm for the drain, so the oil is hot too. The manual’s caution is that hot oil can burn skin, so keep it off your hands and arms.

An ATV and its rider are silhouetted against sunlit dust.

Removing the oil filter

Put towels under the oil filter first, since some oil will run out as it comes away. Then use an oil filter wrench and turn the filter counter-clockwise to remove it.

Next, wipe the filter sealing surface on the crankcase with a clean, dry cloth. A clean seat is what the new filter will seal against.

The manual excerpt reviewed for this guide ends around this point. Fitting the new filter, refilling and checking the level therefore come from your own owner’s manual, which also gives the oil grade and quantity for your model.

Why the engine should not sit empty

The manual states that if the ATV is left without oil for extended periods, the oil pump may lose its prime, which could result in engine damage (Polaris). Its instruction is to replace the oil and filter within a few hours of draining.

It also says not to let the vehicle go overnight without oil. This is why the shopping list comes first: a missing filter on a Sunday afternoon can turn a short job into a problem.

The same page says to change the filter whenever you change the oil. Treat the two parts as one job, not as separate tasks you can space out.

Finding the right figures for your model

This guide gives the order of work, not the numbers that vary by machine. Oil grade, refill quantity and drain plug torque belong to your own manual, which is the document the manufacturer expects you to follow.

With the machine still on level ground, it is a good moment to look at atv tire pressure as well. If anything in your manual is unclear, a qualified technician can confirm the procedure.

Frequently asked questions

Do I replace the filter every time I change the oil?

Show answer

Yes. In the Polaris instructions the filter is swapped together with the oil on every change, not only on some of them.

How long can an ATV sit with the oil drained?

Show answer

Only briefly. The manufacturer’s guidance is to refill within a few hours and never to leave the engine dry through the night, because the oil pump can lose its prime.

Should the engine be warm before I drain it?

Show answer

The Polaris procedure includes a short run of two to three minutes before the drain plug comes out. Keep in mind that this makes the oil hot.

What should I do if hot oil touches my skin?

Show answer

Hot oil can cause burns, so avoid contact in the first place. For any burn, seek medical advice from a qualified professional.

Where do I find the correct torque for the drain plug?

Show answer

Look in the maintenance chapter of your own owner’s manual. The Polaris text only says to tighten the plug to specification, without a value for other models.