Skip to content

Plain-language guides to ATV and quad ownership and riding

Friday, November 20, 2026

Search

Storing an ATV for Winter: Preparation Steps

how to store an atv for winter

Parking your quad for the cold months and worried it won’t start in spring? Here is how to store an ATV for winter: clean and dry it, treat the fuel, look after the battery and tires, then cover it somewhere dry.

This guide covers the end-of-season stage of atv maintenance, with each step tied to a published source.

Item Value
Ride time to spread fuel stabilizer through the system about 10 minutes
Routine oil and air filter service if you skip winterizing every six months, 100 hours of driving, or 1,000 miles
Winterizing start for a machine used mainly in summer after Labor Day
Storage unit size that may fit an ATV plus gear 10×15 or 10×20

These figures come from Synchrony Powersports and Public Storage. They can change, so check the sources and your owner’s manual before you rely on them.

Why does winter storage matter?

Cold, wet months are hard on a parked machine. Can-Am’s storage guide says cold temperatures, snow, and ice can cause serious harm to a vehicle that is not stored properly, with rust, tire flat spots and degraded fuel as the main risks.

You do not always need the full routine. Synchrony notes that a rider who uses the ATV regularly all year can consider skipping winterizing, while anyone with an off-season can save money and headaches by doing it, as the Synchrony Powersports guide explains.

Timing depends on how you ride. A summer-only machine can be winterized after Labor Day, and a hunting rig can wait until the fall season ends, according to the same Synchrony page.

Clean and dry the machine first

Dirt holds moisture against metal, and that is how corrosion starts. Public Storage points out that mud, dirt, grass, and other debris can retain moisture against metal surfaces and contribute to corrosion.

If you need a full walkthrough, the guide on how to clean an atv covers the washing itself. For storage, the order of work matters more than the soap you use.

  1. Wash the frame, wheels, tires and undercarriage, reaching the hard-to-see areas.
  2. Let everything dry completely, using a towel or compressed air for crevices.
  3. Apply a rust inhibitor or anti-corrosion spray to exposed metal parts, as Can-Am advises after drying.

Treat the fuel, fluids and battery

Fuel

Gasoline can degrade while it sits. The usual fix is to fill the tank, add fuel stabilizer, then ride for about 10 minutes so the treated fuel reaches the whole system, per Synchrony. If the machine has a carburetor, the same page says to drain it once the engine has cooled.

Draining the tank is the other route. ATV.com adds a caution: some studies show that an empty fuel system can rot or dry out to the degree that it causes its own set of problems.

Oil, coolant and fogging

Fresh oil is worth the effort. ATV.com says old oil can become acidic and harmful to the engine when left for long periods. On a liquid-cooled machine, the same page says the coolant should be fresh, at the proper level and carry the correct antifreeze mixture.

Synchrony also lists engine fogging, which it calls arguably the most important part of winterizing, because it coats engine parts against corrosion. Follow your manual for the method and approved products.

If you are not winterizing at all, routine oil and air filter service still applies every six months, 100 hours of driving, or 1,000 miles, according to Synchrony Powersports.

Battery

A battery left connected in the cold can go flat. Can-Am recommends removing it and storing it in a cool, dry place, away from freezing temperatures, while ATV.com recommends a smart trickle charger, also called a battery maintainer, to hold the charge without overcharging.

For more on charging and testing, see this page on atv battery maintenance.

Lubricate moving parts and protect the tires

Grease protects what water would otherwise attack. Synchrony suggests a healthy layer of waterproof grease on moving parts, paying particular attention to the chain, drive shaft, U-joints, CV joints, suspension, throttle cable, brake cable and clutch cable. Your manual may name parts that need a special product.

Flat spots form when tires carry the same load in one place for months. ATV.com says radial tires are less prone to this, but bias ply tires are especially prone to flat spots.

Advice on pressure differs. Can-Am suggests adding a few PSI to keep tires round, while ATV.com says to inflate to the recommended pressure, so follow your manual when in doubt. Public Storage adds that you should check tire pressure before storage and again before riding.

An ATV rider is silhouetted against a low sun and drifting dust.

Taking weight off the tires is better still. Use stands or blocks if you can; Public Storage warns that any support must be rated for the vehicle’s weight and follow the manufacturer’s recommendations.

If you cannot lift the machine, ATV.com suggests moving it a few inches every couple of weeks to spread the tire pressure.

Pick the right place and cover

Indoors is the first choice. Can-Am calls a garage, shed or basement the ideal place to store an ATV during the winter, because it shields the machine from cold, snow and swinging temperatures.

When outdoor storage is the only option, Can-Am recommends a high-quality, weatherproof cover and an area that is dry and well ventilated to avoid moisture buildup. Choose a breathable cover, since Public Storage says plastic can trap condensation.

A rented unit is another route. Public Storage says a 10×15 or 10×20 storage unit may provide enough space for an ATV with riding gear and tools, depending on dimensions, so measure the machine first. It also notes that spare or loose batteries cannot be stored separately in its units, so confirm your facility’s rules.

Extra steps for long-term storage

Leaving a machine for a year or more calls for the manufacturer’s own long-term instructions, which Public Storage tells owners to check in the manual.

  • Lubricate the chain and other recommended moving parts.
  • Protect exposed metal from corrosion with a suitable lubricant.
  • Take steps to keep insects and rodents out of the exhaust and air intake.
  • Keep a written checklist of anything to reverse before riding.

Any plugs or cloth used against pests must come out before the engine is started. Writing that on the checklist is the simplest safeguard.

Frequently asked questions

Should I drain the fuel or add stabilizer?

Show answer

Both are accepted routes in the sources. Stabilizer suits a machine you want to leave with a full tank, and draining suits owners who prefer an empty system, with the caveat that dry fuel lines have their own risks.

Can I cover my ATV with a plastic tarp?

Show answer

A tightly wrapped plastic sheet is a poor choice. A fitted, breathable cover lets moisture escape, and the machine should be fully dry underneath it.

What should I check before the first ride in spring?

Show answer

Remove any exhaust or intake plugs, recheck tire pressure, and confirm the battery is charged and reconnected. Then work through your written checklist so nothing from storage is left in place.

Do I need to winterize if I ride through winter?

Show answer

Not necessarily, since the routine mainly protects a machine that will sit idle. Regular servicing still applies, and snow and salt make frequent washing worthwhile.